adjust screw
英 [əˈdʒʌst skruː]
美 [əˈdʒʌst skruː]
网络 调整螺丝
双语例句
- The field glasses adjust with a screw. Most flashlights work on two batteries.
双筒望远镜是用一个旋钮调节焦距的。大多数的手电筒用两节电池。 - For the adjustment of peeling length, just adjust the external socket hex cap screw dispensing with removal of blade.
剥皮长度调整，仅需要调整外部一内六角螺丝，不必拆卸刀片。 - Twin adjust rotation screw on both covers and pistons, to avoid continuous heavy stresses by teeth, shaft, body.
调整旋转双螺杆都涵盖和活塞队，以避免连续沉重压力的牙齿，竖井机构。 - Adjust processing temperature according as the extruder screw. Effect of organic additives on porous silicon nitride ceramics prepared by extrusion method
根据挤出机大小及其螺杆塑化能力适当调整加工温度。有机添加剂对多孔氮化硅陶瓷挤出成型工艺的影响 - Ensure that the punch center and the panel anvil are at the same vertical; If any deviation, adjust the screw on the indenter.
检查冲杆中心是否与枕垫块凹孔中心一致，若有偏差时，可调整冲击块紧母上的内六方镙钉。 - Electrically activities;. When should adjust pulling the area is pulling the machine to loosen the screw, casters activities.
活动脚轮；当要调节拉网机拉网的面积时先要松开活动脚轮，螺丝。 - Striping-cutting structure: Adjust the screw to lift the support plate of feed-in, and ensure the good engagement of driven gears.
切条结构：调整调节螺杆，使左进料托板上移，确定传动齿轮保持啮合。 - Add fine adjust device for the pressure of foot, without dial on the adjustable screw, more convenience for operation.
压脚压力采用微调装置，压力调节螺钉设有刻度，更加方便操作。 - Different from traditional electric and pneumatic screwdriver tools, this screwdriver system can adjust the screw with no axial pressure when driving screws.
区别于现有的电动、气动螺丝刀工具，该螺丝刀系统在驱动螺丝时，能对螺钉头实现无轴向压力的调节。 - The object of this dissertation is to calculate the height of screw mandrils from CAD data and develop a mechanical hand to adjust screw mandrils 'height automatically.
本文主要介绍根据CAD造型数据计算上下模冲压顶杆的高度，并开发一台顶杆高度自动调节机械手调节离散型面模具顶杆高度。 - At the same this paper introduces the principle of three feasible ways to adjust tool that can realize consistency between the zero-position signal positions and the beginning point of original screw helix.
介绍了可以实现零位信号位置与螺纹螺旋线的起点相一致的三种可行的对刀方法的原理。 - Besides, when changing the speed, it is necessary to properly adjust the size of the screw configuration and dies to improve the screw transmission capacity of materials in case of plugging or steam back-flow in the extruder.
另外，在改变转速的同时，要适当调整螺杆配置以及模孔大小，改变螺旋对物料的输送能力以防止堵机、反喷现象的发生。